← Back to catalogue

Spun

Model code EN-DOME

Twenty-five spun metal dome pendants, from a 190 mm bullet to a 600 mm workshop shade. Each shade is available with a standard E27 lamp holder or with an integrated LED behind a flush diffuser.

The range 25 designs

EN-DOME-001 · Classic Wood Dome

A deep half-dome on a turned wood stem. The matt shell keeps the glare inside and throws a clean pool straight down — the default choice over an island or a dining table.

EN-DOME-001 · Classic Wood Dome
Diameter
Ø300 mm
Lamp
E27, or integrated LED
Finish
White–white / black–white
Material
Aluminium / wood

EN-DOME-002 · Heritage Wood Dish

A shallow dish with a rolled rim and a copper interior. The copper warms the light on its way out, so the pool underneath reads softer than the white shell suggests.

EN-DOME-002 · Heritage Wood Dish
Diameter
Ø350 mm
Lamp
E27, or integrated LED
Finish
White–copper
Material
Aluminium / wood

EN-DOME-003 · Saucer Wood Stem

The widest of the shallow shades. A broad saucer spreads light across a table rather than concentrating it, which suits long counters and reception desks.

EN-DOME-003 · Saucer Wood Stem
Diameter
Ø380 mm
Lamp
E27, or integrated LED
Finish
White–white / black–white
Material
Aluminium / wood

EN-DOME-004 · Brass Cap Cone

A tapered cone under a brass cap. Narrow enough to hang in a run of three or five over a counter without the shades crowding each other.

EN-DOME-004 · Brass Cap Cone
Diameter
Ø230 mm
Lamp
E27, or integrated LED
Finish
Black–gold / white–gold
Material
Aluminium / wood

EN-DOME-005 · Workshop Dome

The factory shade, in five diameters. At Ø600 it becomes an architectural object rather than a light fitting — worth hanging alone over a large table.

EN-DOME-005 · Workshop Dome
Diameter
Ø300 / Ø400 / Ø450 / Ø500 / Ø600 mm
Lamp
E27 + 3 W accent LED, or integrated LED
Finish
Black
Material
Aluminium / metal

EN-DOME-006 · Handled Workshop Dome

The workshop dome with a cast handle over the top. Six diameters, so a single detail can carry through a whole scheme at different scales.

EN-DOME-006 · Handled Workshop Dome
Diameter
Ø300 / Ø350 / Ø400 / Ø450 / Ø500 / Ø600 mm
Lamp
E27 + 3 W accent LED, or integrated LED
Finish
Black
Material
Aluminium / metal

EN-DOME-007 · Scandi Rounded Dome

A rounded shoulder that softens where it meets the ceiling flex. Quieter than the factory shades and easier to place in a room that is already busy.

EN-DOME-007 · Scandi Rounded Dome
Diameter
Ø350 mm
Lamp
E27, or integrated LED
Finish
White–white / black–white
Material
Aluminium

EN-DOME-008 · Low Disc Wood Collar

A low disc with a wood collar at the neck. The shallow profile keeps sightlines open, which matters when the fitting hangs at eye level across a room.

EN-DOME-008 · Low Disc Wood Collar
Diameter
Ø350 mm
Lamp
E27, or integrated LED
Finish
White–white / black–white
Material
Aluminium / wood

EN-DOME-009 · Hammered Copper Onion

Hand-hammered copper over an onion profile. The dimpled surface breaks up reflections, so the shade reads as texture rather than as a mirror.

EN-DOME-009 · Hammered Copper Onion
Diameter
Ø250 / Ø320 mm
Lamp
E27, or integrated LED
Finish
Copper–gold
Material
Aluminium

EN-DOME-010 · Polished Brass Capsule

A tall capsule in polished brass. The narrow mouth makes a tight, bright pool — good over a bar, less so where you want general fill.

EN-DOME-010 · Polished Brass Capsule
Diameter
Ø350 mm
Lamp
E27, or integrated LED
Finish
Antique brass–gold
Material
Aluminium

EN-DOME-011 · Hammered Brass Half Dome

A true half sphere in hammered brass. The gold interior bounces light back across the full width of the mouth, so the spread is wider than the shape suggests.

EN-DOME-011 · Hammered Brass Half Dome
Diameter
Ø300 / Ø400 mm
Lamp
E27, or integrated LED
Finish
Antique brass–gold
Material
Aluminium

EN-DOME-012 · Utility Handle Dome

The smallest shade in the range, with a utility yoke and copper fittings. Sized for a run over a narrow counter, or as task light beside a workbench.

EN-DOME-012 · Utility Handle Dome
Diameter
Ø225 mm
Lamp
E27, or integrated LED
Finish
White–white / black–white
Material
Aluminium

EN-DOME-013 · Black Gold Band Dome

A matt black dome cut by a brushed gold band at the rim. The band catches light at the edge and gives the shade an outline from across a room.

EN-DOME-013 · Black Gold Band Dome
Diameter
Ø400 mm
Lamp
E27, or integrated LED
Finish
Black–gold / white–gold
Material
Aluminium

EN-DOME-014 · Brass Neck Cone

A steep cone on an exposed brass neck. The angle keeps the lamp well recessed, so there is no glare from a seated position.

EN-DOME-014 · Brass Neck Cone
Diameter
Ø300 mm
Lamp
E27, or integrated LED
Finish
White–white / black–white
Material
Aluminium

EN-DOME-015 · Stepped Factory Dome

A stepped shoulder above a flared skirt — the classic enamel factory shade, in two diameters. The step is structural, not decorative.

EN-DOME-015 · Stepped Factory Dome
Diameter
Ø360 / Ø460 mm
Lamp
E27, or integrated LED
Finish
White–white / black–white
Material
Aluminium

EN-DOME-016 · Rustic Silver Dome

An aged silver finish with a deliberately uneven surface. No two shades weather identically, which is the point.

EN-DOME-016 · Rustic Silver Dome
Diameter
Ø350 mm
Lamp
E27, or integrated LED
Finish
Silver–white
Material
Aluminium / metal

EN-DOME-017 · Faceted Black Dome

A faceted shell rather than a spun curve. Each panel takes light at a slightly different angle, so the shade shifts as you move past it.

EN-DOME-017 · Faceted Black Dome
Diameter
Ø300 / Ø400 mm
Lamp
E27, or integrated LED
Finish
Black–gold / white–gold
Material
Aluminium / metal

EN-DOME-018 · Square Handle Warehouse

A deep warehouse dome under a squared steel yoke. The heaviest-looking shade in the range, and the one that best carries an industrial interior.

EN-DOME-018 · Square Handle Warehouse
Diameter
Ø300 mm
Lamp
E27, or integrated LED
Finish
Black–gold / white–gold
Material
Aluminium / metal

EN-DOME-019 · Sculpted Teardrop

A drawn teardrop with a long shoulder. Three diameters and four finish pairings — the most configurable shade in the range.

EN-DOME-019 · Sculpted Teardrop
Diameter
Ø250 / Ø320 / Ø420 mm
Lamp
E27, or integrated LED
Finish
Black–gold / black–white / white–gold / white–white
Material
Aluminium

EN-DOME-020 · Flared Saucer

A sharply flared saucer with a gold interior. Almost flat, so it disappears against a ceiling until it is lit.

EN-DOME-020 · Flared Saucer
Diameter
Ø360 mm
Lamp
E27, or integrated LED
Finish
Black–gold
Material
Aluminium

EN-DOME-021 · White Granite Dome

A stone-effect finish over a spun dome. Reads as marble at a distance and holds up close, where a printed pattern usually will not.

EN-DOME-021 · White Granite Dome
Diameter
Ø300 / Ø400 mm
Lamp
E27, or integrated LED
Finish
White granite
Material
Aluminium

EN-DOME-022 · Antique Brass Handle Bell

A small bell in antique brass with a hooped handle. Narrow enough to hang in a tight run, and heavy enough not to look like an afterthought.

EN-DOME-022 · Antique Brass Handle Bell
Diameter
Ø190 mm
Lamp
E27, or integrated LED
Finish
Antique brass
Material
Aluminium

EN-DOME-023 · UFO Wide Dome

A very shallow disc with a lit underside. Sits close to flat, which makes it the right answer where a deep shade would hang into a sightline.

EN-DOME-023 · UFO Wide Dome
Diameter
Ø300 mm
Lamp
E27, or integrated LED
Finish
Black
Material
Metal

EN-DOME-024 · Hammered Copper Hemisphere

A full hemisphere in hammered copper. The exact half-sphere is what separates it from the onion and the half dome — no shoulder, no taper.

EN-DOME-024 · Hammered Copper Hemisphere
Diameter
Ø300 mm
Lamp
E27, or integrated LED
Finish
Hammered copper
Material
Metal

EN-DOME-025 · Antique Gold Bullet

A narrow bullet in antique gold. The tightest beam in the range, intended to be hung low and close over a specific surface.

EN-DOME-025 · Antique Gold Bullet
Diameter
Ø190 mm
Lamp
E27, or integrated LED
Finish
Antique gold
Material
Metal

Applications

Magnetic-track versions are a build option, not separate codes — order the shade you want and specify CIANA or Elance′ on the enquiry.

Browse the full Enlighten Pro catalogue

Made on our own tooling

Enlighten Pro controls the manufacturing chain from raw aluminium to finished luminaire — which is why a specification can be held, a finish repeated, and a batch traced.

Our own moulds and dies

The tooling behind our castings and extrusions is ours — ADC-12 for pressure die casting, AL6063 for extrusion.

Machining in-house

CNC machining centres, VMC and precision lathes. Every cast and extruded component is machined here for final precision.

Powder coating in-house

Our own line — coated, cured and inspected to exact RAL specifications, so finishes match across a project and across repeat orders.

See all fifteen processes  ·  Browse the full catalogue